2014 - Mazda6 - Engine

RADAR SENSOR AIMING [MAZDA RADAR CRUISE CONTROL (MRCC) SYSTEM]

WARNING:

• Radiofrequency radiation exposure information:

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

• This equipment should be kept with minimum distance of 20 cm {7.9 in} between the radiator (antenna) and your body at all times during adjustment.

• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

• If the radar sensor aiming adjustment is not completed, the Mazda radar cruise control (MRCC) system, and the forward obstruction warning (FOW) system will not operate normally which could lead to an unexpected accident. Therefore, when performing the following work, always perform the aiming adjustment so that the MRCC system, and the FOW system operate normally.

• Vehicle control module (V/C-module) removal/installation, replacement

• Radar sensor, radar sensor bracket removal/installation, replacement

1. Park the vehicle on level ground.

CAUTION:

• If the vehicle and reflector are set at different heights or different angles, accurate adjustment cannot be performed.

• Level ground conditions must be within 1 degree for the front and back, and right and left.

• Perform the work in an area where 8 m {26 ft} or more of space from the vehicle front and 4 m {13 ft} or more of width are available.

• Perform the aiming adjustment in a place where there is no obstruction up to approx. 1.2 m {3.9 ft} from the road surface at approx. 8 m {26 ft} from vehicle front.

• Remove cargo from the cabin and trunk compartment so that the vehicle is in an unloaded condition.

• Adjust the tire pressure of each tire to the specified value.

• Do not let foreign matter (metal, plastic material) get into the aiming implementation area to prevent radio wave interference.

• Do not move or shake the vehicle during aiming adjustment (such as riding in or opening a door).

• Remove dust or dirt from the radiator grille ornament.

• Do not turn the power off during the aiming adjustment.

• The voltage supplied to the radar sensor must be 9.5—15.5 V.

• The aiming adjustment must be performed under approx. -30—60 °C {-22—140 °F} conditions.

2. Adjust the SST (plum-bob) so that it is aligned with the center of the brand emblem, determine the center position at the front of the vehicle, and mark the center position (point A) on the floor surface.

NOTE:

• The center of the brand emblem indicates the center position of the vehicle.

3. Adjust the SST (plum-bob) so that it is aligned with the center of the brand emblem, determine the center position at the rear of the vehicle, and mark the center position (point B) on the floor surface.

NOTE:

• The center of the brand emblem indicates the center position of the vehicle.

4. Secure the end of the leveling line over point B.

NOTE:

• Use a commercially-available leveling line.

5. Pull the unsecured end of the leveling line over the vehicle and to the front and adjust it so that it passes over point A.

6. Mark the line (position A) at the point 5 m {16 ft} from point A and in the direction forward of the vehicle.

NOTE:

• If the leveling line is secured at the vehicle front center point (point A), the leveling line may deviate. Therefore, secure the leveling line in the order of point B, point C, and point A.

7. Install the SST (reflector and plum bob) to the SST (tripod).

8. Adjust so that the height of the SST (reflector) from the floor surface is 710 mm {28.0 in}.

9. Level the SST (reflector) by adjusting the leveling bubble on the SST (tripod) so that it is centered on the bubble reference line.

NOTE:

• A commercially-available tripod equipped with a level can be substituted for the SST (stand).

10. Set the SST (stand) with the SST (plum-bob) and the marking aligned.

NOTE:

• Visually verify that the reflection surface of the reflector faces the vehicle.

11. Visually inspect the surfaces of the radar sensor and the radiator grille ornament for the following:

• Dirt is adhering to radar sensor surface

• Dirt is adhering to radiator grille ornament surface

• Foreign matter (reflective object) is adhering to radar sensor

• Foreign matter (reflective object) is adhering to radiator grille ornament surface

12. Connect the M-MDS to the DLC-2.

CAUTION:

• If the engine is started, the aiming may not be performed correctly due to oscillation. Perform the aiming with the engine stopped.

13. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

a. Select "Electrical".

b. Select "SBS/MRCC".

c. Select "Reader Aiming".

14. Perform the aiming adjustment following the instructions on the screen.

15. If "Aiming has been unsuccessful." is displayed on the screen, repair according to the error code in the following chart.

• If verification and repair are completed, perform the aiming adjustment again.

CAUTION:

• If an error occurs during the aiming adjustment, DTC C1A67:54 will be stored. If this DTC has been stored, the aiming adjustment cannot be performed. To perform the aiming adjustment again, switch the ignition off (LOCK), clear the DTC, and perform the adjustment.

Error code	Item	Possible cause	Inspection item (s)
Code 1	Improper target position	SST (reflector) installation mistake Marking setting mistake Improper installation of radar sensor Radar sensor and vehicle control module (V/C-module) malfunction	SST (reflector) installation condition Marking setting condition (SST string) Radar sensor installation condition and installation part condition Applicable DTC troubleshooting
Code 2	Improper target angle	SST (reflector) installation mistake Marking setting mistake Improper installation of radar sensor Radar sensor and vehicle control module (V/C-module) malfunction	SST (reflector) installation condition Marking setting condition (SST string) Radar sensor installation condition and installation part condition Applicable DTC troubleshooting
Code 3	Multiple targets	A is reflective object in area around SST (reflector) could become a possible target Radar sensor and vehicle control module (V/C-module) malfunction	Remove reflective object in area around SST (reflector) which could become a possible target Applicable DTC troubleshooting
Code 4	Target moves	SST (reflector) moves (within radar sensor reception range) during aiming Radar sensor and vehicle control module (V/C-module) malfunction	SST (reflector) installation condition Applicable DTC troubleshooting
Code 5	No target	Voltage supplied to radar sensor is out of specification Aiming performed under out-of-specification temperature Dirt is adhering to radar sensor or radiator grille ornament SST (reflector) does not exist (within radar sensor reception range) during aiming Radar sensor and vehicle control module (V/C-module) malfunction	Radar sensor supply voltage inspection (approx. 9.5—15.5 V) Ambient temperature verification (approx. -30—60 °C {-22—140 °F}) Remove dirt from radar senor or radiator grille ornament surface SST (reflector) installation condition Applicable DTC troubleshooting
Code 7	Vehicle condition malfunction	Vehicle moves during aiming Vehicle door opening/closing, getting on vehicle Change in wheel speed Radar sensor and vehicle control module (V/C-module) malfunction	Verification of selector lever position (in P position) (ATX) Verification of shift lever position (in neutral position) (MTX)
Code 8	Recording fails	Communication error between radar sensor and vehicle control module (V/C-module) Radar sensor and vehicle control module (V/C-module) malfunction	Applicable DTC troubleshooting